Universal Design Model Ordinance

Assembly Bill 2787 (Chapter 726 of Statutes of 2002) required the Department to develop guidelines and at least one Universal Design Model Ordinance (PDF) applicable to new construction and home modifications for voluntary adoption by local governments.

The Department’s New Home Universal Design Option Checklist (PDF) identifies rooms and denotes features which must be offered by a builder in residential units subject to the ordinance that are being newly constructed or substantially rehabilitated. These features would only be installed if requested by the buyer/owner and would not cause an unreasonable delay or significant unreimbursable costs to the developer or builder.

In general, the model ordinance provides:

  • Definitions for critical terms
  • Local option as to types of units (owner-occupied and/or rental), and number of units
  • Specific exemptions and enforcement mechanisms

Examples of rooms and areas in covered units for which it is mandatory to offer certain design features:

General Room

Bathrooms/Powder Room

Kitchen on the primary entry level

  • Accessible path of travel to dwelling
  • 32" wide interior doors
  • Handrail and handrail reinforcement in hallways
  • Entry door high/low peep hole viewer
  • Doorbell at 48" maximum height in accessible location (36")
  • Switches and outlets at 15" to 48" above the floor
  • Rocker light switches
  • Closet rods and shelves adjustable from 3' to 5'6" high
  • Up to 42” wide hallway
  • At least one bathroom or powder room on the primary entry level
  • Grab bars and grab bar backing in walls
  • 30" x 48 clear space at fixtures
  • Lavatory with lever faucet controls
  • Removable base cabinets or open lavatory with knee space and protection panel
  • Clear space for a 48” to 60” diameter circle
  • Accessible bathtub or roll-in shower
  • Hand-held adjustable shower head
  • Accessible route to the kitchen
  • 30" x 48" clear space at appliances
  • Removable base cabinets at sink
  • 30" x 48" clear space at sink
  • Lever controls at kitchen sink faucet
  • Switches and outlets at 15" to 48" above the floor
  • 18” counter or breadboard for clear work area

New Home Universal Design Checklist (AB 1400)

Assembly Bill 1400 (Chapter 648 of Statutes of 2003) requires HCD to develop guidelines and adopt a New Home Universal Design Option Checklist (PDF). HCD developed the first checklist in 2005 and an additional checklist in 2007. Both checklists cover the requirements of the law; however, the 2007 New Home Universal Design Option checklist may be considered more user friendly for consumers and builders. 

The statute specifically requires:

  • That the checklist covers single-family dwellings, duplex, triplex, townhouse, condominium, or other dwellings.
  • That the checklist include specified standards and features, and any other requested by the buyer at a reasonable time, if reasonably available and feasible to install or construct
  • That the developer and buyer be permitted to agree in writing to different standards if they are clearly disclosed.
  • That each feature be indicated on the list as "standard," "limited," "optional," or "not available."
  • That the list includes at what point in the construction process the buyer must notify the developer that the buyer wishes to purchase the features.
  • That the developer is not required to provide any feature on the list.
  • That the Department can develop, certify, and make available a standard form providing the checklist information, and that a developer’s use of a form substantially the same as that developed and distributed by the Department is deemed to comply with the law.

The introductory section of the Checklists provides information as to the house being purchased and clarifies, in plain English, the statutory requirements and how the form works.  The table below identifies where in the checklists information is found.

Description of Information in Checklist

2005 Checklist

2007 Checklist

Features that might be available and are being disclosed. The form allows the developer to provide abbreviated information regarding the status (as “standard,” “limited,” “optional,” or “not available”), timing (suggested periods are in the introductory section), details (a reference to other parts in the checklist for specific information), and cost of construction or installation.

Part I Part III
Features available for common rooms, bedrooms, and laundry areas, following the same format as the previous part. Part II Part IV
Direction for specified attachments, rather than requiring additional details and writing on the form itself, as well as certifications to ensure both parties that they have provided or received, and considered, all required information. Part III Part V

Either form (2005 or 2007) is a standard available to those who want to use it. Its use, in substantially the same form, is deemed compliant with the statute.  Any builder, however, may develop its own form as long as it complies with the requirements of the statute.

Additional Resources

For more information, check the resources listed as well as Information Bulletin 2005-13 (SHL) (PDF)